In other words, in countries where the above six factors score highly, we would also expect higher degrees of reported happiness. But the report points out three countries where this was not the case.
In this context of changing and challenging market requirements, Gas Insulated Substation GIS has found a broad range of applications in power systems for more than two decades because of its high reliability, easy maintenance and small ground space requirement etc.
SF6 has been of considerable technological interest as an insulation medium in GIS because of its superior insulating properties, high dielectric strength at relatively low pressure and its thermal and chemical stability. SF6 is generally found to be very sensitive to field perturbations such as those caused by conductor surface imperfections and by conducting particle contaminants.
The presence of contamination can therefore be a problem with gas insulated substations operating at high fields. If the effects of these particles could be eliminated, then this would improve the reliability of compressed gas insulated substation.
It would also offer the possibility of operating at higher fields to affect a potential reduction in the GIS size with subsequent savings in the cost of manufacture and installation. The purpose of this paper is to develop techniques, which will formulate the basic equations that will govern the movement of metallic particles like aluminum, copper in a coated as well as uncoated busduct.
In recent years, the areas of industrial application of AC drives, especially Induction machine based on DTC technique has gradually increased due to its advantages over the other techniques of control.
However conventional DTC suffers from high torque ripple and variable switching frequency. This paper, propose a method to reduce torque fluctuations, where the circular flux vector is divided into twelve sectors and is compared with conventional DTC method where the flux vector is divided into six.
Electrical and Electronic Engineering Vol. F and Sansui H, "Simulink model of direct torque control of Induction machine", American journal of applied sciences 5 8: Krishnan, Electric Motor Drives: Enhancing Reusability of Conventional Apollo Modules by proposing change in design and use of new ablative material Enhancing Reusability of Conventional Apollo Modules by proposing change in design and use of new ablative material Abstract: The paper deals with the reusability of command modules used during Apollo space missions.
During Apollo missions in 's the module surface becomes charred up to some extent, hence decreasing the strength and scope of further reusability of the module.
A new design has been proposed and simulation results have revealed the possibility to reuse the module again for another mission. The new design has incorporated an in-built mechanism that will extend some part of the module surface outwards near to the periphery of the base of the module.
The design, mechanism, material and other details are discussed in succeeding sections. New ablative material has been introduced for more getting more promising results. Design patterns have been the target of a great deal of research in the last few years. A design pattern is a general solution to a commonly occurring problem.
They are composed of three parts: This paper concentrates on developing a catalog for design patterns for safety-critical real-time systems and allows flexibility to choose, search a design pattern and add more design patterns. This tool will be able to help generate the code for the suitable design pattern.
Edition published in Safety assessment of design patterns for safety-critical embedded systems. Sarma, Sahith Rampelli, Dr. High-resolution signal parameter estimation is a significant problem in many signal processing applications. Such applications include direction of arrival DOA estimation for narrow band signals and wideband signal emitted by multiple sources and received by sensor arrays.
Strong consistency of the modified method is established. However, an important disadvantage of the ULA geometry in DOA estimation is that it can only estimate the azimuth angle.
To estimate the elevation angle, Uniform circular arrays UCA geometries and planner array are employed in many applications.
Schmidt, "Multiple emitter location and signal parameter estimation". Antennas and Propagation, vol. A Face recognition scheme using hybrid approach is proposed in this paper. Feature vector based on eigen vectors of sub images is used for recognition Image is partitioned in to sub images.
Sub parts are rearranged in to rows and column matrices. Eigenvectors are computed for these matrices.Dr. Raj Kishore Sharma is a teacher, speaker, advisor, author and researcher.
He joined the Institute on July 17, He has nearly 15 years of Industrial experience and 19 years of teaching experience. Measuring Happiness Levels in Mumbai: Methodology Methodology Happiness has been defined either as a broad notion of how one feels about their life in general or as an emotional or affective 8 Pages (3, Words) - Last Modified: 23rd March, 3-D Printer 1.
A 3-D printer is a machine that prints objects by laying down successive layers of plastic or other materials. 3-D printers have existed since the s.
Measuring happiness for social scientific purposes is usually realized as a part of a ‘survey’ in which a lot of people answer the same questions, either in face-to-face interviews or on questionnaires presented on the web.
Coriander is an amazing herb that is used for culinary and medicinal purposes.
From the oldest times it is known in the Mediterranean region, Africa and the Middle East, central Asia, India and China.1 The old Greeks, Egyptians and Romans were familiar with it. I’ve already written about the concept of Gross National Happiness (GNH) a lot.
But attending the international GNH conference in Paro, Bhutan, I have improved my understanding of what GNH really means. In a couple of blog posts, I want to outline the methodology, the survey findings, and the actual use of GNH as a policy tool.